Entity Settings

Last published at: August 4th, 2025
Delete

In the <Entity> Settings you can configure Plauti Deduplicate settings that can differ per entity, such as the Result Fields.

To configure the Entity Settings for a certain entity:

  1. In the Plauti Deduplicate app, at left, go to Manage Entities
  2. At the entity you want to configure settings for, click Manage  at right.
  3. Go to the <Entity> Settings tab.

General Settings

Result Fields - Duplicate Check Job Results

Delete

After a Duplicate Check job is finished, its results are shown on the Duplicate Check Job Results page. The Result Fields are the entity fields that are shown in the job results.

To change which entity fields are shown in DC Job results: 

  1. At "Result Fields - Duplicate Check Job Results", click Edit.
  2. Move the entity fields you want to display to the Selected Fields column.
  3. Click Save.

This job result shows result fields Account Name, Address 1: City, Address Phone, and Website

The result fields that are shown on tab "Duplicates Found" for single record duplicates, can be set in the Duplicate Prevention‍ settings.

In the Lead Settings you'll find two additional settings:

  • Account Cross Entity Result Fields - Duplicate Check Job Results
  • Contact Cross Entity Result Fields - Duplicate Check Job Results

These are intended for the Account and Contact results of a Cross-Entity‍ Duplicate Check job, and are configured in the same way as the regular Result Fields setting for Duplicate Check Job Results.

Delete Entity Configuration

This option will delete the entity and all of its configuration, so including scenarios and feature configuration, from the Plauti Deduplicate Setup. This cannot be undone! Of course you can always add the entity again at a later point, but it will need to be fully reconfigured again, including all scenarios and feature settings.

To delete an entity's full configuration from the Plauti Deduplicate Setup, click Delete at "Delete Entity Configuration".

Disabled Records

Plauti Deduplicate only marks active records as duplicates when searching for duplicates. Define which records of this entity are regarded as 'disabled' in your environment. These records will not be marked as duplicate.

For each listed status, set the status reasons that indicate a disabled (inactive) record.
If all status reasons indicate an active record, leave the Status Reason field empty. This will usually be the case for statuses such as the "Active" status: if all status reasons for the "Active" status indicate an active record, leave the field empty.

Most common configuration for Contacts: no status reason entered for 'Active' because all its status reasons indicate active records.

Most common configuration for Leads: no status reason entered for 'Open' because all its status reasons indicate active records.
Qualified, canceled etc records indicate inactive records.

Advanced Settings

Start Entity Setup Process for Entity

When the Plauti Deduplicate setup for an entity is published for the first time, customizations are applied to forms and ribbons. Because of this, the first publish of an entity setup is of the type "Publish All".

When you make any changes to your forms or ribbons, or add a form to use in an app, the Plauti Deduplicate setup needs to be re-published for all entities where you want to use Plauti Deduplicate. This way the necessary customizations are added to the new or edited form or ribbon.

Click Start Entity Setup to start a publish of the entity's setup of the type "Publish All". This will add Plauti Deduplicate customizations to all forms of the entity.
Just clicking "Publish" after making changes within the Plauti Deduplicate Setup is not sufficient, as it will only add the Plauti Deduplicate setup changes you made to forms.

Start Entity Teardown Process for Entity

Where the above setting "Delete Entity Configuration" removes an entity and its configuration from the Plauti Deduplicate setup, Entity Teardown removes all Plauti Deduplicate features from an entity. 

Click Start Entity Teardown to fully remove Plauti Deduplicate from an entity. In the process of deleting the Plauti Deduplicate app from your environment, first apply Entity Teardown to each entity configured in Plauti Deduplicate. Then delete the solution. Read more about deleting the Plauti Deduplicate app in Uninstall Plauti Deduplicate for Dynamics 365‍.

Abort Ongoing Setup/Teardown Process for Entity

The first time Plauti Deduplicate Setup is published for an entity, this should take about 5 minutes. An Entity Teardown process should also take up comparable time. If it takes significantly longer, the process might be stuck somewhere. To fix this, you can try to stop the setup publish or teardown for the entity, then try again.

Click Abort Entity Setup/Teardown   to try and stop an ongoing system Entity Setup or Teardown process for an entity.